• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

KB6NU's Ham Radio Blog

KB6NU's Ham Radio Blog
  • HOME
  • Study Guides
  • Teach a One-Day Tech Class
  • W8SRC Repeater Guide
  • Advertise
  • Hire Me

FCC’s OET clarifies emissions compliance testing for RF LED lighting devices

July 4, 2016 By Dan KB6NU 1 Comment

Have any of you had RFI problems with your LED lights? I haven’t here….Dan

ARRL logo type_17QST de W1AW
ARRL Bulletin 22  ARLB022
From ARRL Headquarters
Newington CT  June 30, 2016
To all radio amateurs

SB QST ARL ARLB022
ARLB022 FCC’s OET Clarifies Emissions Compliance Testing for RF LED Lighting Devices

The FCC’s Office of Engineering and Technology (OET) has clarified that all RF LED lighting devices falling under Part 15 rules as “unintentional radiators” must meet conducted and radiated emissions limits set forth in those rules.

“Operation of Part 15 unintentional radiators is subject to the condition that no harmful interference is caused,” the OET reminded, in a knowledge database paper released on June 17. “Manufacturers and users should therefore note that lighting devices are required to cease operation, if harmful interference occurs.”

The OET said radiated emissions measurements must be performed at least from 30 MHz to 1000 MHz to adequately demonstrate compliance with Part 15 (15.109). Its guidance, the OET continued, applies to RF LED lighting devices that, in the past, have been considered to operate on frequencies below 1.705 MHz. Previously, devices operating between 9 kHz and 1705 kHz had to be tested only for radiated emissions up to 30 MHz, where no specified radiated emissions limits exist, and were exempt from testing from 30 MHz to 1000 MHz. The OET said it recognizes that routine radiated emissions measurements are needed under Part 15, based on the highest frequency generated or used in the device.

“[W]e have found that emissions from RF LED lighting devices are non-periodic, broadband in nature, and are produced as a byproduct of the internal driver circuitry within the RF LED lighting device,” the OET “knowledge database” paper said. “These types of emissions have adequate energy and potential to generate radiated emissions well above 30 MHz.”

The ARRL Lab’s Electromagnetic Compatibility Engineer Mike Gruber, W1MG, said he was pleased to see the FCC’s OET clarify the test measurement requirements. He said ARRL is generally hearing more RFI complaints stemming from RF LED bulbs.

“Not only are the emissions limits higher for Part 15 LED bulbs – as opposed to Part 18 fluorescent and CFL bulbs, they seem to be winning out in terms of consumer popularity,” Gruber said. “Higher limits and more bulbs probably make for more complaints.” Gruber said the Lab has seen LED lighting devices causing problems in the 2 meter band. “Since conducted emissions limits do not apply above 30 MHz, radiated emissions limits can be the first line of defense against RFI at these higher frequencies.”

Gruber pointed out that noise generated by street and traffic lighting can be widespread. In such instances, he suggested that Part 15b limits for residential areas should apply. “These limits are lower than Part 15a limits, which are intended only for commercial and industrial environments,” he explained. “This is especially critical in cases where a pole transformer connected to the lighting device also feeds a home or residence. The 240 V split-phase secondary system can conduct RF into a residence through the service entrance panel.” He suggested that the lower limits may benefit mobile users.

The OET noted that the ANSI Accredited Standards Committee C63-EMC is drafting measurement procedures for lighting devices. “When complete, we expect it will address in greater detail the measurement procedures and configurations to be used in determining compliance,” the OET said.
NNNN
/EX

 

Related posts:

  1. ARLB030 ARRL Asks FCC to Clarify that Hams May Modify Non-Amateur Gear for Amateur Use
  2. Contest Aims to Measure Interference Caused by Home-Networking Devices
  3. Noise floor report interesting, but I’m not optimistic
  4. ARRL Again Complains to FCC about Illegal Marketing of Electronic Lighting Ballasts

Filed Under: EMI/RFI

Reader Interactions

Comments

  1. Steve K8BGR says

    July 5, 2016 at 9:19 am

    I had an RFI problem with LED bulbs and my garage door opener. The opener has sockets for two bulbs. All was well until I installed LED bulbs. Then it seemed that the remote control became flaky. Sometimes it would work, sometimes not. Eventually I isolated the cause to the LED bulbs. Whenever they were on, the remote didn’t work. I replaced the bulbs with incandescents and haven’t had a problem since.

    Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

No Nonsense Technician Class License Study Guide (for tests given between July 2026 and June 2030)

New No Nonsense Technican Class Study Guide now available!

The 2026 version of my Tech Class study guide is now available, and as always, the PDF version is FREE!. The ePub version costs $11.97, and a Kindle version and paperback version will be available on Amazon shortly.

Click here to get all of my "No Nonsense" study guides.

Also available: The CW Geek's Guide to Having Fun with Morse Code

W5SWL.Com
Retevis Ailunce H1 DMR Radio
DXpander: Cobweb antennas, Laser Cutting

You’ve got mail!

Enter your email address below and get an email every time I publish a new post.

Email


I frequently teach classes to help newcomers get their licenses. The next class will take place on Saturday, October 10, 2026 on the University of Michigan campus. Click here for more information.

If you can't make the class, subscribe to the mailing list to be notified of when the next class will be held.

You can always download my free study guide, and if you have any questions about the classes, or amateur radio in general, please feel free to email me directly.

Support KB6NU.Com

Donate $7.30 and get two of these cool stickers. Measuring 4.25-in. W by 2.75-in. H, it's perfect for your car, your shack, or wherever!

Contact me

If you have a question or comment about one of my blog posts, or a question about any of the material in my study guides, or just a question about ham radio in general, you can email me at [email protected].

Blogs You Should Also Read

  • AE5X: A CW-centric blog from Kingswood, Texas
  • K0LWC Blog
  • LA3ZA Ham Radio Blog
  • Little Radios, Big Fun – WB3GCK
  • Mr. Vacuum Tube's Blog
  • Radio Artisan – K3NG
  • The K0NR Weblog
  • VE3WDM's QRP Ham Radio Blog
  • W2LJ’s Blog

Ham Radio Websites

  • Dashtoons – The Hammin' Comedy by Jeff K1NSS

Podcasts

  • ICQ Podcast
  • Linux in the Ham Schack
  • No Nonsense Amateur Radio Podcast
  • Resonant Frequency Amateur Radio Podcast

Recent Comments

  • Mir Labs on Ten Steps to Mastering Morse Code
  • Skip K4EAK on Is the ARRL finally feeling the heat?
  • Victor on 468: Ham Radio’s Magic Number
  • Goody K3NG on Not1MM now working on my Linux box!
  • Mir Labs on JA1NUT: Two Issues in Morse Code Learning

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

Footer

Copyright © 2026 Daniel M. Romanchik, KB6NU · Log in